Hypertherm MAXPRO200 vs XPR170 - Speed or Cut Quality?

Date

October 20, 2026

The Hypertherm MAXPRO200 and the Hypertherm XPR170 are the two power sources Australian fabrication shops most often weigh against each other when they buy a Plazmax machine. They are not the same class of system. The MAXPRO200 is a 200 amp LongLife system built for fast, economical mild steel cutting. The XPR170 is the entry point to Hypertherm's X-Definition platform: a more capable and considerably more expensive premium system, bought for what it does to the edge of the part and for what it can cut beyond mild steel. Both pierce structural plate, and on a spec sheet their amperages look close. The choice comes down to one question: is the part you cut most often judged on how fast it came off the table, or on the edge and the holes?

This article puts the two side by side on actual cut chart data from Hypertherm's own instruction manuals, so the decision is made on numbers, and then says plainly what the numbers do not show.

What each system is for

The MAXPRO200 is a LongLife oxygen and air plasma system built for fast, economical straight cutting. Hypertherm's cut charts give it the higher mild steel cut speed of the two at every thickness from 10 to 32mm on the same O2 plasma / Air shield process. It runs simple consumable sets, it is quick to set up, and it earns its keep on the structural work that fills most Australian fabrication shops every week: cleats, base plates, gussets, stiffeners and brackets, where the part is welded straight off the table and nobody measures the edge.

The XPR170 is Hypertherm's X-Definition platform at 170 amps. It is the system we recommend when cut quality is the specification: square, consistent edges on mild steel, good bolt holes straight off the table with True Hole on mild steel, and the ability to cut stainless steel and aluminium with a proper edge rather than just getting through them. It cuts mild steel a little slower than the MAXPRO200 at the same thickness. It cuts it better, and it cuts the materials the MAXPRO200 is not designed for.

Cut speed on mild steel - the MAXPRO200 is the faster machine

The following cut speeds are taken from the MAXPRO200 Instruction Manual (IM 807700, Revision 9.4, Table 18) and the XPR Cut Chart Instruction Manual (IM 809830, Revision 9), both for the O2 plasma / Air shield process on mild steel, above water, with the MAXPRO200 at 200 A and the XPR170 at 170 A.

Thickness (mm)MAXPRO200, 200 A (mm/min)XPR170, 170 A (mm/min)Speed advantage - MAXPRO200
103,7353,4618% faster
152,8452,27725% faster
201,9201,57522% faster
251,4301,17522% faster
328057527% faster

Read that honestly. At 15 to 25mm, the thickness band where most structural cleats and base plates live, the MAXPRO200 is cutting around 22 to 25% faster than the XPR170 on the same material. On a shift of straight-cut structural parts that is a real difference in output, and it is the reason the MAXPRO200 is the right machine for a lot of Australian shops.

The XPR170 is not slow, but if the only thing that matters about the part is how quickly it came off the table, the cut charts favour the MAXPRO200. If you need X-Definition cut quality and the speed as well, the answer is not the XPR170 - it is the XPR300, which on the same O2 plasma / Air shield process cuts 20mm mild steel at 2,550 mm/min and 25mm at 1,950 mm/min: faster than the MAXPRO200 at every thickness in the table, with the X-Definition edge. The XPR300 vs XPR170 comparison sets that out in full.

Pierce capacity

Pierce capacity is the thickness a system can start a cut in the middle of the plate, which is what nest cutting needs. Severance, the thickness a system will part from an edge start, is a bigger number and a less useful one.

Mild steelMAXPRO200XPR170
Production pierce32mm40mm (argon assist, VWI or OptiMix console)
Edge start from38mm44mm

MAXPRO200 figures are from Table 18 of IM 807700 Revision 9.4; XPR170 figures from IM 809830 Revision 9.

The XPR170 pierces thicker, to 40mm with argon assist on the VWI console that is standard on Plazmax machines, against 32mm for the MAXPRO200. If your work regularly includes nest-cut parts in 32 to 40mm plate, that alone decides it. Below 32mm both systems pierce everything you put on the table, and the decision moves to the next section.

Cut quality - where the XPR170 earns its price

The cut charts measure speed and thickness. They do not measure the edge, and the edge is the whole argument for the XPR170.

X-Definition is Hypertherm's highest cut quality plasma process. Hypertherm describe its core process range on mild steel as virtually dross free, with square cut edges and sharp top edges, and the system manages arc response and gas control automatically to hold that quality across the life of the consumables. On a Plazmax machine the XPR170 runs with True Hole on mild steel, which is what gives bolt holes that are round, with minimal taper and no divot at the end of the cut, so the part can go to the welder without a drill or a reamer touching it. For a shop making parts where holes are bolted to other people's steel, that is the feature customers notice first.

The MAXPRO200 produces a good, square, weldable edge on mild steel for its class. Hypertherm's manual sets out how to optimise its cut quality and its LongLife process is designed to extend consumable life. It is not an X-Definition process and does not run True Hole. On a cleat or a base plate that is welded straight off the table, that difference does not matter. On a part with holes that have to bolt up first time, or a visible edge that the customer will see, it does.

On stainless steel and aluminium the gap is wider. The XPR170 with the VWI console uses water injection shielding on stainless and runs dedicated non-ferrous processes that give a clean, bright edge. The MAXPRO200 has cut charts for both materials on air or nitrogen and will get through them, but it is a mild steel system first. If stainless or aluminium parts are a regular part of your work rather than an occasional job, the XPR170 is the system to look at.

Marking - the feature the MAXPRO200 does not have

The XPR170 (and the whole XPR range) can mark the plate as well as cut it, and the MAXPRO200 cannot. On a nest of structural parts that is not a small difference, because it decides how much of the job leaves the table finished.

Marking is a low current plasma process, run at 18 amps on the XPR170 against 170 amps for cutting, that scribes a visible line into the surface of the plate without piercing or cutting through it. The torch runs along the marked path at marking speed, the arc transfers at a fraction of cutting current, and the result is a clean line about 2mm wide. Hypertherm publish the marking parameters inside each cutting process in the XPR cut charts, so on mild steel the torch marks and then cuts on the same consumable set, with no consumable change between the two.

In practice, that means the nest carries the information the next trade needs: fold lines for the press brake, centre marks for holes that will be drilled or tapped, and part numbers and job numbers scribed into each part. On the MAXPRO200 all of that is done by hand after cutting, with a tape, a square and a scriber, or by sending the drawing to the shop floor and hoping it is read correctly. On a Plazmax machine running the XPR170 it comes off the table with the part, in the right place, every time, straight from the nesting software.

Two process options are published for the XPR170 on mild steel. Nitrogen marking runs at 6,350 mm/min and is fast enough that marking adds very little to the cycle time of a nest. Argon marking runs at 2,540 mm/min and gives a finer, more controlled line; it needs the CorePlus console or above, and the VWI console fitted as standard to XPR systems on Plazmax machines includes it. Mark depth is adjustable: slower torch speed and higher current make a deeper mark, faster and lower make a shallower one. Hypertherm note that marking is not suited to plate under 1.5mm, where the mark can burn through, and they recommend alternating marking and cutting across the nest rather than marking everything first, which helps consumable life.

Figures are from the XPR Cut Chart Instruction Manual, IM 809830 Revision 9, 170 A O2 plasma / Air shield process, marking rows.

Bevel cutting

Both systems bevel. The MAXPRO200 has dedicated extreme bevel consumables and published bevel cut charts at 130 A and 200 A on mild steel, and it handles weld-prep bevels on structural plate well. The XPR170 bevels on the standard consumable set and, with True Bevel on mild steel, holds the angle and the land through the cut with less operator correction. When the torch tips over, the arc travels through more material than the nominal plate thickness: a 45 degree bevel on 25mm plate is around 35mm of material at the torch angle. On either system, size the power source to the bevel thickness, not the flat plate thickness.

Which system is right for your operation?

Choose the MAXPRO200 if your daily work is mild steel in the 6 to 32mm range, most parts are welded straight off the table, throughput on structural plate is what the machine is bought for, and stainless or aluminium is occasional. It is the faster and the simpler of the two on that work, and it costs less to buy and to run.

Choose the XPR170 if the edge is part of the specification: bolt holes that must fit without drilling, visible edges, parts going to paint or to a customer's inspection, regular stainless or aluminium work, nest cutting in plate above 32mm, or parts that need fold lines, hole centres or part numbers marked on them before they leave the table. It cuts mild steel slightly slower than the MAXPRO200 and it cuts it to a standard the MAXPRO200 is not designed to reach.

Look at the XPR300 if you want both: the X-Definition edge and the holes, and throughput on 20 to 40mm plate that beats the MAXPRO200. It is the step up from the XPR170 in amperage, cut speed and pierce capacity (50mm on mild steel with argon assist), on the same platform and the same consumable architecture. For a structural shop that cuts a lot of 20 to 40mm plate and cannot give up edge quality, it is usually the right machine.

If you are between the MAXPRO200 and the XPR170, the question to ask is what happens to your parts after they come off the table. If the answer is "they get welded", the MAXPRO200 is probably the right machine. If the answer involves a drill, a grinder or a rejection, it is the XPR170. And if the answer is "both, and we cut a lot of it", it is the XPR300.

Both systems on Plazmax machines

Plazmax integrates both the MAXPRO200 and the XPR170 as power source options on the CutAce and CutPro CNC plasma cutting systems, designed and built in New Zealand for Australian conditions. XPR systems on Plazmax machines are configured with the VWI (Vented Water Injection) console as standard, which enables argon-assist piercing and water injection shielding for stainless steel.

As the manufacturer, we commission the power source integration and provide installation and operator training. Plazmax machines in Australia are supported by Plazmax service agents, backed by the Plazmax technical team. We supply genuine Hypertherm MAXPRO200 consumables and XPR consumables and parts for both systems, dispatched the same business day on most items and shipped Australia wide.

For full technical specifications and cut chart data on each system, see:

To discuss which system is right for your specific application, contact the Plazmax team.

Frequently asked questions

Is the MAXPRO200 faster than the XPR170?

On mild steel, yes. Hypertherm's cut charts for the O2 plasma / Air shield process show the MAXPRO200 at 200 A cutting 7 to 25% faster than the XPR170 at 170 A across 10 to 32mm, with the biggest advantage at 15 to 25mm. The XPR170's advantage is cut quality, hole quality and non-ferrous capability, not mild steel speed.

Can the MAXPRO200 cut stainless steel and aluminium?

Yes. It has published cut charts for both on air and nitrogen. It is a mild steel system first, and the edge it produces on non-ferrous plate is not the X-Definition edge of the XPR170. For occasional stainless or aluminium it is fine; for regular non-ferrous work the XPR170 is the better fit.

What is the maximum thickness each system will pierce on mild steel?

The MAXPRO200 pierces mild steel to 32mm at 200 A, with edge starts from 38mm. The XPR170 pierces to 40mm with argon assist on a VWI or OptiMix console, with edge starts above that. Both figures are from the current Hypertherm instruction manuals.

Can the MAXPRO200 mark or etch parts?

No. The MAXPRO200 has no marking process in its instruction manual. The XPR170, and the whole XPR range, marks with nitrogen or argon at low current on the same consumables it cuts with, scribing fold lines, hole centres and part numbers into the plate without cutting through it.

What if I need the cut quality and the speed?

That is the XPR300. It runs the same X-Definition process as the XPR170, with True Hole and True Bevel on mild steel, and its 300 A cut speeds on mild steel are higher than the MAXPRO200's at 10, 15, 20 and 25mm (4,500 / 3,440 / 2,550 / 1,950 mm/min against 3,735 / 2,845 / 1,920 / 1,430), with production pierce to 50mm. See Hypertherm XPR300 vs XPR170 for the cut chart comparison.

Does the XPR170 cost more to run?

The consumable sets are different and are not interchangeable, and the XPR170 runs more gas options. Whether it costs more per part depends on what the part is: on a straight-cut structural part the MAXPRO200 is the more economical machine, while on a part that would otherwise need drilling, grinding or a second operation, the XPR170 removes that cost. Contact Plazmax with your typical parts and we will work it through with you.

Can I get consumables for a MAXPRO200 or XPR170 on another manufacturer's machine?

Yes. Plazmax supplies genuine Hypertherm MAXPRO200 and XPR consumables and parts Australia wide, whichever machine the power source is fitted to.

Request for information

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
Name*
This site is protected by reCAPTCHA.
By submitting this form I agree to the Privacy Policy, and that Plazmax may use this information to respond to my enquiry and for marketing and communication purposes.

Hypertherm XPR

Aluminum

Hypertherm XPR

Stainless Steel

Hypertherm XPR

Mild Steel